Lectrosonics DM812 User Manual download pdf (Page 9)

DM Series Installation Guide

Rio Rancho, NM

In a stacked conﬁguration, one unit must be conﬁgured

as the Master unit and the others as Slave units. Con-

ﬁguring a unit as a Master or a Slave can be done using

the front panel LCD and controls or the Control Panel

GUI interface.

Note: In order to use the convenient Control Panel

GUI, LecNet2™ must be installed on the attached

computer system. (See Installing LecNet2™

Software and USB Driver.)

To connect the Master/Slave units, plug one end of a 12

inch Cat5e cable (two are supplied with each with unit)

to the transmit (TX) port on the Master unit, and con-

nect the other end to the corresponding receiver (RX)

port on the Slave unit immediately below the Master.

Repeat this procedure with the second Cat5e cable.

(See Expansion Port Digital Audio Network Interface

Interconnection Diagram.)

CAUTION: Do not connect these ports to each

other on a single unit, and to not cross the

cables between the units.

Master/Slave Conﬁguration

When stacking multiple units, one unit is always set as

the Master and all subsequent units are set as Slaves.

The LCD interface is used to do this.

PROGRAMMABLE INPUTS/OUTPUTS

1 - GND

2 - IN 1

3 - IN 3

4 - IN 5

5 - IN 7

6 - IN 9

7 - IN 11

8 - GND

9 - OUT 1

10 - OUT 3

11- OUT 5

12 - OUT 7

13 - GND

14 - +5V

15 - IN 2

16 - IN 4

17 - IN 6

18 - IN 8

19 - IN 10

20 - +5V

21 - OUT 2

22 - OUT 4

23 - OUT 6

24 - OUT 8

25 +5V

ccw cw

OFF

OUT 3

OUT 4

OUT 1

IN 1

IN 2

IN 3

500 Ohms

LED

Potentiometer

Switch

Programmable Inputs

Wiring Diagram Example

Three Programmable Inputs:

2 - 10 K linear potentiometers

for volume control

1 - Toggle switch for muting

3 Programmable Outputs:

LEDS for function indicators

(380 to 500 Ohm resistors in-line

to avoid burning out LEDS)

NOTE

Common Connections can be used for

all voltage and ground connections

among all devices.

WARNING: The Expansion I/O connectors are

NOT EtherNet, CobraNet or any other network

based device interconnects. Connecting them

to Ethernet, CobraNet or other network based

device may cause damage to either unit.

14 25

1 - GND

2 - IN 12

3 - IN 14

4 - IN 16

5 - IN 18

6 - IN 20

7 - IN 22

8 - GND

9 - OUT 9

10 - OUT 11

11 - OUT 13

12 - OUT 15

13 - GND

14 - +5V

15 - IN 13

16 - IN 15

17 - IN 17

18 - IN 19

19 - IN 21

20 - +5V

21 - OUT 10

22 - OUT 12

23 - OUT 14

24 - OUT 16

25 - +5V

1 - GND

2 - IN 1

3 - IN 3

4 - IN 5

5 - IN 7

6 - IN 9

7 - IN 11

8 - GND

9 - OUT 1

10 - OUT 3

11 - OUT 5

12 - OUT 7

13 - GND

14 - +5V

15 - IN 2

16 - IN 4

17 - IN 6

18 - IN 8

19 - IN 10

20 - +5V

21 - OUT 2

22 - OUT 4

23 - OUT 6

24 - OUT 8

25 - +5V

LOGIC I/O CONNECTIONS UPPER CONNECTOR

LOGIC I/O CONNECTIONS LOWER CONNECTOR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Lectrosonics DM812 User Manual Page 9

Comments to this Manuals

Related products and manuals for Audio accessories Lectrosonics DM812