Lectrosonics UCR511 User Manual download pdf (Page 12)

UCR511

In the two user programmable frequency groups, up to

16 frequencies can be programmed per group.

Note

The Tuning Setup Screen only selects the tuning mode (NORMAL or

Group Tuning) and not the operating frequency. Actual operating

frequencies are chosen through the Frequency Window.

If NORMAL tuning mode is selected, the SEL Up and

Down buttons select the operating frequency in single

channel (100 kHz) increments and the MENU+Up and

MENU+Down shortcuts tune in 16 channel (1.6 MHz)

increments.

There are two group tuning modes: factory present

groups (Grp A through D) and user programmable

frequency groups (Grp U and V).

In these modes, the SEL Up and Down buttons navigate

among the selected intermod-free frequencies in the

group and the MENU+Up and MENU+Down shortcuts

jump to the first and last frequencies in the group.

Also, a lower case a, b, c, d, u or v will be displayed to

the immediate left of the transmitter switch settings in the

Frequency Window. The letter identifies the selected

factory or user tuning group.

Any time the currently tuned frequency is not in the

current tuning group, the group tuning mode indicator

will blink. Any time the currently tuned frequency is in

the current turning group, the group tuning mode indica-

tor will give a steady (non-blinking) indication.

If a factory tuning group has been selected, pressing

either the SEL Up or Down button will select the nearest

factory selected frequency in that group above or below

the current frequency.

User Programmable Frequency Group Behavior

The user programmable frequency groups work very

similar to the factory groups with a few exceptions. The

most obvious difference is the ability to add or remove

frequencies from the group. Less obvious is the behav-

ior of a user programmable frequency group with only

one, or no entries.

A user programmable frequency group with only one

entry will only display that one frequency regardless of

how many times the SEL Up or Down buttons are

pressed (providing the MENU button is not pressed at

the same time).

A user programmable frequency group with no entries

reverts to non-group-mode behavior, i.e., access is

allowed to all 256 available frequencies in the selected

receiver module's frequency block. However, once a

frequency has been added to the tuning group, this

behavior changes to group-mode behavior where the

MENU button must be pressed and held while either the

SEL Up or Down buttons are pressed to access frequen-

cies that are not part of the current tuning group.

Adding/Deleting User Programmable Frequency

Group Entries

Note

Each User Programmable Frequency Group (“u” or “v”) has

separate contents. It is suggested to review the section titled

Frequency Coordination prior to adding frequencies inorder to

minimize potential intermodulation problems.

1. Start from the Frequency Window and verify

that a lower case “u” or “v” is present next to

the transmitter switch settings.

2. While pressing and holding the MENU button

press either the SEL Up or Down button to

move to one of the 256 available frequencies

in the block. Whenever the selection comes to

rest on a frequency that is in the current

group, the group tuning mode indicator (letter

"u" or "v") will give a steady indication. On

frequencies that are not in the group, the

indicator will blink.

3. To add or remove the displayed frequency

from the group, hold down the MENU button

while pressing and holding the SEL Up button.

The group tuning mode indicator will stop

blinking to show that the frequency has been

added to the group, or begin blinking to

indicate that the frequency has been removed

from the group.T

COMPAT

The COMPAT setup screen selects

the type of transmitter used with the

UCR511. The available modes are:

500 - Lectrosonics 500 Series.

This is the default setting

and should be used if your transmitter supports

it. This mode offers the best audio quality.

COMPAT

500

100 - Lectrosonics 110 Series compatibility mode.

300 - Lectrosonics 300 Series compatibility mode.

MODE 3 - Compatible with certain non-Lectrosonics

transmitters.

IFB - Compatible with Lectrosonics IFB transmitters.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 27 28

Comments to this Manuals

No comments

Lectrosonics UCR511 User Manual Page 12

Comments to this Manuals

Related products and manuals for Equipment Lectrosonics UCR511