Lectrosonics UDR200b User Manual download pdf (Page 10)

USING THE LED INFORMATION DISPLAY

0 V

500 250

100

1uV 2 1mV

OPTI

BLEND

500 250

100

1uV 2 1mV

OPTI

BLEND

LIM 0

-6

-12 -18 -24

-30

-36 -42 -48

TX AUDIO LEVEL dB

RF LEVEL

FREQ

SELECT

POWER

MONITOR

MODE

A B

DIVERSITY

1 0 8.7 1

The UDR200B has three power up options and four menu

options which control all aspects of the receiver’s operation.

POWER UP OPTIONS

Toggle Battery Monitor Display- Holding in the UP button

while powering on the receiver will toggle on and off the LED

display that indicates the transmitter battery voltage. (Note:

the battery status display will not function unless a valid pilot

tone is being received.)

FREQ

SELECT

POWER

Turning off the battery status display prevents confusion when

the UDR200B receiver is used with 195 Series or early 200

Series transmitters that lack the battery monitor function.

When toggled off, the first LED display to appear (following the

brief status displays) will indicate the receiver frequency and

TV channel.

Set/Reset Hard Lock Mode - Holding down the MENU button

while powering on the receiver will switch the receiver between

the UNLOCKED mode and the HARD LOCKED mode.

FREQ

SELECT

POWER

In the UNLOCKED mode, all receiver menu options may be

adjusted. In the HARD LOCKED mode, the MENU button may

be used to scroll through the menus, but no adjustments may

be made. If this option is selected, the receiver will display its

current status for about 2 seconds after turn on before revert-

ing to the Set Receiver Frequency menu.

Set LecNet Address - Holding down the DOWN button while

powering on the receiver allows the LecNet address of the

receiver to be set.

FREQ

SELECT

POWER

Setting each UDR200B to a unique address is critical when

more than one receiver is connected to a PC. The address

setting should be accomplished before starting the LecNet

Master Pro application. UDR200Bs are shipped from the

factory with a LecNet address of 150. Multiple UDR200Bs in a

system should be assigned unique addresses above 150. You

will see the following displayed on the LED display of the

UDR200B in the address setting mode:

L E C N E T A D D R : 1 5 0

Use the UP and DOWN buttons to set the receiver to an

unused address. Then press the MENU button. This will store

the new address, and put the UDR200B in its normal operating

mode.

MENU OPTIONS

Press the menu button to select the desired menu option.

Each menu option is described below.

Set Receiver Frequency/Display Tx Battery Voltage - When

the receiver is powered up in the “Display Battery Status”

power up mode and the transmitter is turned on, the following

will be shown:

668.100 8.7V 19

This display is only shown in the “Display Battery Status”

power up mode. It will not appear when the battery status

display is toggled off.

Set Receiver Frequency/Display TV Channel - This display

will appear first when the battery monitor option is toggled off.

It will also appear when the MENU buttion is pressed if the

battery monitor option is toggled on. This menu allows the

receiver frequency to be set either to the stored frequencies in

the currently active group or to any frequency in the receiver’s

block in 100kHz steps. You will see the following menu option

displayed on the LED display of the UDR200B in the frequency

setting mode:

668.100 TV47 19

The first number shows the current receiver frequency in MHz,

the second shows the UHF TV channel in which the current

frequency falls, and the third shows the transmitter (TX) setting

which matches the current receiver frequency. The TX setting

will flash if no valid Pilot Tone is detected at the current fre-

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 21 22

Comments to this Manuals

No comments

Lectrosonics UDR200b User Manual Page 10

Comments to this Manuals

Related products and manuals for Equipment Lectrosonics UDR200b