INSTRUCTION MANUAL TM Digital IEM System Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.com
QUADRA LECTROSONICS, INC.10 Master(1,2) mode AUDIO CH. 1 2 NO FUNCTION NO FUNCTION MASTER VOLUME MASTER VOLUME AUDIO CH. 1 NO FUNCTION Master
Digital IEM System Split 3,4 Operation Split modes allow you to use a single M4T transmitter running in the 4 Channel mode to send two diffe
QUADRA LECTROSONICS, INC.12 Single Channel Operation The Single mode allows you to use one M4T transmit-ter running in the 4 Channel mode to sen
Digital IEM System Additional Setup Options Tune To select your RF operating frequency, choose Tune in the menu list, and press the MENU/SEL butto
QUADRA PRE-GAIN Limiter This feature can be used in order to provide audio lim-iting at the receiver in order to prevent excessive levels at t
Digital IEM System Factory Defaults This is used if you intend to reset the receiver back to fa
QUADRA The first five presets, A - E, are permanently loaded with the most common channel setup and knob con-figuration combinations: Factory A
Digital IEM System Rio Rancho, NM 17 Accessories P/N 25984 replacement wire belt clip. CCM4R Foam lined carrying case. BCHINGED Spring-loaded belt cli
QUADRA Transmitter Front Panel TM DIGITAL IEM Headphone Channel Select Buttons Power Monitor Switch Transmitter Rear Panel DIGITAL IEM TRANSMITTE
Digital IEM System Initial Setup Connect AC power to the M4T transmitter using the provided power cable. To ensure that the power ca
QUADRA LECTROSONICS, INC. 2
QUADRA Transmitter Menus To access the setup menus, press the MENU/SEL but-ton at the upper left of the membrane panel. To back up one level
Digital IEM System Audio Trim When using analog inputs, this feature gives you the opportunity to adjust the transmitter
QUADRA 3. Insert the adapter plate (the one with threaded Rack Mount Hardware nuts) into the slot behind the front panel. Insert two The M4
Digital IEM System 7. Attach the antenna wires to the antenna ports on the back of the transmitters. 8. Attach the supplied antenna cable protector
QUADRA Single Unit Rack-Mount Instructions Optional RMPM4T-1 Kit This kit is required to rack mount a single transmitter. Assembling the optio
Digital IEM System 9. Attach the supplied antenna and antenna connec-tor guard. Note that this item will fit tightly and is meant to deform slightly d
QUADRA LECTROSONICS, INC.26 Replacement Parts P/N 25989 rack ear flange P/N 14247 rack handle P/N 35702 hex key (allen wre
Digital IEM System Firmware Updates As new versions of the firmware become available, updates are accomplished with a software uti
QUADRA Troubleshooting GuideSymptom Cause Action Transmitter and receiver on, receiver shows strong RF signal, but no blue RF LED on rece
Digital IEM System Service and R
Digital IEM System Table of Contents FCC Notice ...
Digital IEM System Rio Rancho, NM 31
LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provide
QUADRA FCC Notice NOTE: This
Digital IEM System System Overview The Quadra system provides an entirely new level of audio and RF
QUADRA Receiver Operation Battery Insertion The receiver is powered by three AA batteries, either alkaline, lithium, or rechargeable types. Do not
Digital IEM System Body Placement Position the receiver on a belt, guitar strap, wardrobe, etc. so that the antennas are oriented vertically and no
QUADRA LECTROSONICS, INC.8 MASTER VOLUME AUDIO CH. 1 2 NO FUNCTION NO FUNCTION Master(1,2) mode MASTER VOLUME Master(1)+2 mode AUDIO CH. 1 A
Digital IEM System Rio Rancho, NM 9 4 Channel Operation In this mode, all four audio channels fed to the trans-mitter are available at the r
Comments to this Manuals